Solar Guppy - All Things Solar Forum

It is currently Thu Mar 28, 2024 7:00 pm GMT EthGMT

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: MorningStar Mppt - Serial pinout question RX light on solid
PostPosted: Mon May 19, 2008 9:41 pm GMT EthGMT 
Offline
Minnow
Minnow
User avatar

Joined: Thu May 15, 2008 12:51 pm GMT EthGMT
Posts: 11
Location: PA-NJ area
Hello Solar Guppy,

I got my Meterbus adapter today from Morningstar, and I'm looking at a mess of gender benders, terminal adapters, serial to RJ adapters, parallel to serial adapters, rollover cables, modem & null modem adapters etc..

I've tried every combination of everything I have laying around and the best I can get is the RX on solid and the TX blinking within SC-View.

I guess I have two questions. Does it take a while for the data to load into SC-View for the first time? And, the Meterbus instructions show a serial cable between the Meterbus adapter and the PC. Is that really needed or can I just plug the meterbus directly into my serial port? I think a standard serial cable is basically "straight through", so I wouldn't think it's needed. The meterbus adapter is kinda clunky so the serial cable would be nicer sticking out of the back of the PC.

Either way I'm not having much luck. Let me know if you have any ideas.

Thanks!


Top
 Profile  
 
 Post subject:
PostPosted: Tue May 20, 2008 8:09 am GMT EthGMT 
Offline
Red Cobra Delta Guppy
Red Cobra Delta Guppy
User avatar

Joined: Sun Jun 02, 2002 1:01 am GMT EndGMT
Posts: 1159
Location: Lakeland Florida
Its a straight thru cable on the PC to MS adapter, then the standard RJ11 from the adapter to the SunSaver Mppt. If you like you can connect the MS adapter directly to the PC's RS232 ( or a USB to RS232 adapter )

Make sure you have dip switch #4 in the on position ( SUnSaver Mppt )and that the Sunsaver is connected to a battery.


Top
 Profile  
 
 Post subject:
PostPosted: Thu May 22, 2008 1:42 pm GMT EndGMT 
Offline
Minnow
Minnow
User avatar

Joined: Thu May 15, 2008 12:51 pm GMT EthGMT
Posts: 11
Location: PA-NJ area
Green full battery LED is lit solid, with heartbeat LED blinking green on controller. I tried multiple RJ-11 cords (both 2-wire and 4-wire). DIP #4 is up.

I confirmed a standard serial cable is straight through pin 1 --> pin 1, pin 2 --> pin2, etc.. so it's kinda pointless to even use the cable since I have easy access to my serial port. So I plug the Modbus directly into the PC serial.

I'm going to give it another try tonight on a different PC, hope I have better luck there..


Top
 Profile  
 
 Post subject:
PostPosted: Thu May 22, 2008 6:43 pm GMT EndGMT 
Offline
Red Cobra Delta Guppy
Red Cobra Delta Guppy
User avatar

Joined: Sun Jun 02, 2002 1:01 am GMT EndGMT
Posts: 1159
Location: Lakeland Florida
The RJ11 is a 6 wire, not 4 or 2. This should be explained in the SunSaver Manual


Top
 Profile  
 
 Post subject:
PostPosted: Thu May 22, 2008 10:32 pm GMT EndGMT 
Offline
Minnow
Minnow
User avatar

Joined: Thu May 15, 2008 12:51 pm GMT EthGMT
Posts: 11
Location: PA-NJ area
Finally! got it working using another PC.. Not sure what's going on with the laptop.

Sorry for the RJ-11 confusion.. I tried a 2-wire (pins 3&4) since nothing was working and I had nothing to loose. The instruction sheet does show 6-pin, but 4-pin works fine (pins 2,3,4,5) since they duplicated pins 1&2 and 5&6.

Pinout for RJ-11:
1 = GND
2 = GND
3 = TX/RX
4 = GND
5 = Power
6 = Power

Thanks again for the software.. looks great so far.


Top
 Profile  
 
 Post subject: Re: MorningStar Mppt - Serial pinout question RX light on solid
PostPosted: Thu Mar 12, 2009 3:43 am GMT EthGMT 
Offline
Fish Eggs
Fish Eggs
User avatar

Joined: Sat Aug 09, 2008 9:30 am GMT EthGMT
Posts: 6
Location: Norway
Last year when I hooked up the SS MPPT to my computer for the first time I used an ATEN UC-232A USB-to-serial dongle that I borrowed at work. This dongle worked fine with both SC-View and MSView.

I did not find a seller for the ATEN so I ordered a ST Labs U-224 USB-to-serial dongle but I can't get it to work. I tried it with an AVR evaluation board and it works but I can't get it to work with the SS MPPT and SC-View or MSView. Any ideas?

Thanks!

OS


Top
 Profile  
 
 Post subject: Re: MorningStar Mppt - Serial pinout question RX light on solid
PostPosted: Thu Mar 12, 2009 9:06 am GMT EthGMT 
Offline
Red Cobra Delta Guppy
Red Cobra Delta Guppy
User avatar

Joined: Sun Jun 02, 2002 1:01 am GMT EndGMT
Posts: 1159
Location: Lakeland Florida
Both SC-View and MS-View use RTS/DTR to generate power for the isolation interface ... my guess is the USB dongle you purchased doesn't have those pins. I've used literally 6-7 different generic converters over the years and never had an issue.


Top
 Profile  
 
 Post subject: Re: MorningStar Mppt - Serial pinout question RX light on solid
PostPosted: Thu Dec 02, 2010 10:45 am GMT EndGMT 
Offline
Guppy
Guppy
User avatar

Joined: Fri Aug 04, 2006 10:24 am GMT EthGMT
Posts: 284
Location: Los Angeles
Hmmm... MS Tristar MPPT has 3 interfaces, and I've been most successful with MSView with the serial port. Never got data thru the modbus and its adapter, or the Ethernet port. I guess I'll try the serial port first when I'm at the system in late December.


http://tinyurl.com/LMR-Solar

_________________
"Since the dawn of time it has been mankind's dream to blot out the sun"
Montgomery Burns


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
cron
Powered by phpBB © 2000 - 2020 phpBB Group

phpBB SEO

© SGT 2002 - 2020 Solar Guppy